<?xml version="1.0" encoding="UTF-8"?>
<rss version="2.0" xmlns:atom="http://www.w3.org/2005/Atom">
  <channel>
    <title>EIGENROOM 실전 노트</title>
    <link>https://eigenroom.com/ko/journal</link>
    <atom:link href="https://eigenroom.com/ko/journal/rss.xml" rel="self" type="application/rss+xml"/>
    <description>PID, 주파수 설계, 상태공간, 추정을 실제 설계 판단과 재현 가능한 브라우저 실험으로 설명하는 제어공학 노트입니다.</description>
    <language>ko</language>
    <lastBuildDate>Sun, 15 Nov 2026 00:00:00 GMT</lastBuildDate>
    <item><title>진상 보상기가 φmax만큼 위상여유를 늘리지 못하는 이유</title><link>https://eigenroom.com/ko/journal/lead-adds-less-than-phi-max</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/lead-adds-less-than-phi-max</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>주파수 설계 실무</category><description>진상 보상기는 한 주파수에서만 최대 위상을 내고 루프 이득도 올립니다. 그래서 교차 주파수가 대상의 위상이 더 낮은 곳으로 옮겨 갑니다. 그 대가를 각도로 계산해 봅니다.</description></item>
    <item><title>메이슨 이득 공식과 블록선도 축소, 어느 쪽이 빠를까?</title><link>https://eigenroom.com/ko/journal/mason-or-block-reduction</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/mason-or-block-reduction</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>모델링 실무</category><description>두 방법의 결과는 같습니다. 루프가 안쪽으로 겹겹이 있거나 나란히 이어져 있으면 블록선도 축소가, 루프가 서로 걸쳐 있거나 경로가 여럿이면 메이슨 이득 공식이 빠릅니다.</description></item>
    <item><title>LQR의 Q와 R을 어림짐작 없이 고르는 법</title><link>https://eigenroom.com/ko/journal/choosing-lqr-weights</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/choosing-lqr-weights</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>설계 판단</category><description>Q = I, R = 1은 단위에 따라 뜻이 바뀝니다. 브라이슨 규칙은 가중치를 허용 크기로 바꿉니다. 상태가 둘인 이송축으로 가중치의 배율이 무엇을 바꾸고 무엇을 바꾸지 않는지 봅니다.</description></item>
    <item><title>개루프가 불안정할 때 나이퀴스트 선도 읽기</title><link>https://eigenroom.com/ko/journal/nyquist-with-an-unstable-open-loop</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/nyquist-with-an-unstable-open-loop</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>안정성 점검</category><description>우반평면 극점이 하나 있으면 곡선이 −1을 반시계 방향으로 한 번 감싸야 하고, 이득이 너무 작아도 너무 클 때처럼 불안정합니다. 먼저 세고 나서 여유를 읽으세요.</description></item>
    <item><title>시간 지연: 이득으로 되찾을 수 없는 한계</title><link>https://eigenroom.com/ko/journal/dead-time-limits-bandwidth</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/dead-time-limits-bandwidth</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>주파수 설계의 한계</category><description>시간 지연은 크기를 그대로 두고 주파수에 비례해 위상을 빼앗습니다. 실험실 모터에서는 100 ms마다 교차 주파수의 위상여유가 19.5°씩 줄며, 되찾으려면 루프를 느리게 하는 수밖에 없습니다.</description></item>
    <item><title>제어기 이산화: 영차 홀드 등가, 쌍일차 변환, 샘플링 주기</title><link>https://eigenroom.com/ko/journal/discretizing-a-controller</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/discretizing-a-controller</guid><pubDate>Sun, 15 Nov 2026 00:00:00 GMT</pubDate><category>디지털 구현</category><description>샘플링 루프는 주기의 절반쯤 되는 지연을 치르고, 이산화 방법도 오차를 더합니다. 실험실 모터에서 80 ms 주기는 위상여유 41°를, 10 ms 주기는 5°를 잃게 합니다.</description></item>
    <item><title>z극점이 작다고 기계가 더 빠른 것은 아니다</title><link>https://eigenroom.com/ko/journal/a-smaller-z-pole-is-not-always-faster</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/a-smaller-z-pole-is-not-always-faster</guid><pubDate>Mon, 05 Oct 2026 00:00:00 GMT</pubDate><category>측정과 설계</category><description>두 기록의 샘플링 주기가 다르면 극점 크기만 비교해 설계 결론을 내릴 수 없습니다. 먼저 시계를 맞춰야 합니다.</description></item>
    <item><title>센서 기록이 진동을 숨길 수 있다</title><link>https://eigenroom.com/ko/journal/the-sensor-log-can-hide-an-oscillation</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/the-sensor-log-can-hide-an-oscillation</guid><pubDate>Mon, 05 Oct 2026 00:00:00 GMT</pubDate><category>측정과 설계</category><description>매끈한 그래프가 샘플링의 결과일 수 있습니다. 제어기를 다시 조정하기 전에 기록의 측정 방식을 확인하세요.</description></item>
    <item><title>피드포워드가 피드백을 대신하지는 않는다</title><link>https://eigenroom.com/ko/journal/feedforward-does-not-replace-feedback</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/feedforward-does-not-replace-feedback</guid><pubDate>Mon, 05 Oct 2026 00:00:00 GMT</pubDate><category>측정과 설계</category><description>모델로 오차 발생 전에 예상 입력을 줄 수 있습니다. 실전의 다음 질문은 그 예상이 틀렸을 때 무엇이 일어나는가입니다.</description></item>
    <item><title>피드백이 실제로 줄이는 오차는 무엇일까?</title><link>https://eigenroom.com/ko/journal/which-error-does-feedback-reduce</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/which-error-does-feedback-reduce</guid><pubDate>Sun, 04 Oct 2026 00:00:00 GMT</pubDate><category>실전 신호 읽기</category><description>센서 이득이 있으면 합산점 오차가 작아도 실제 추종 오차는 클 수 있습니다.</description></item>
    <item><title>움직이는 목표에는 다른 추종 시험이 필요하다</title><link>https://eigenroom.com/ko/journal/a-moving-target-needs-a-different-test</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/a-moving-target-needs-a-different-test</guid><pubDate>Sun, 04 Oct 2026 00:00:00 GMT</pubDate><category>설계 실전</category><description>계단 오차가 0이어도 램프 오차는 남을 수 있습니다. 실제 요구 입력으로 시험하세요.</description></item>
    <item><title>양의 계수가 안정성 증명은 아니다</title><link>https://eigenroom.com/ko/journal/positive-coefficients-are-not-enough</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/positive-coefficients-are-not-enough</guid><pubDate>Sun, 04 Oct 2026 00:00:00 GMT</pubDate><category>안정성 점검</category><description>계수가 모두 양수인 3차식에도 발산하는 모드 두 개가 있을 수 있습니다.</description></item>
    <item><title>가장 빠른 관측기가 항상 좋지는 않은 이유</title><link>https://eigenroom.com/ko/journal/fast-observers-have-a-cost</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/fast-observers-have-a-cost</guid><pubDate>Sat, 03 Oct 2026 00:00:00 GMT</pubDate><category>설계 실전</category><description>관측기가 잡음 섞인 위치 측정을 더 강하게 보정에 쓰면 제어 입력은 어떻게 될까요?</description></item>
    <item><title>탱크 하나에 선형 모델이 여러 개인 이유</title><link>https://eigenroom.com/ko/journal/one-tank-many-linear-models</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/one-tank-many-linear-models</guid><pubDate>Sat, 03 Oct 2026 00:00:00 GMT</pubDate><category>설계 실전</category><description>낮은 작동 수위와 높은 작동 수위에서 같은 시간척도로 반응할까요?</description></item>
    <item><title>어느 RLC 공진을 측정했나요?</title><link>https://eigenroom.com/ko/journal/which-rlc-resonance</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/which-rlc-resonance</guid><pubDate>Sat, 03 Oct 2026 00:00:00 GMT</pubDate><category>설계 실전</category><description>커패시터 전압이 가장 커지는 주파수는 항상 ωn = 1/√(LC)일까요?</description></item>
    <item><title>히터는 냉각기가 아니다: 이득보다 제어 능력부터</title><link>https://eigenroom.com/ko/journal/a-heater-cannot-cool</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/a-heater-cannot-cool</guid><pubDate>Sat, 03 Oct 2026 00:00:00 GMT</pubDate><category>구동기와 설계</category><description>열 시스템으로 느린 동역학·불가능한 목표·적분 와인드업을 구분합니다. 좋은 이득으로 없는 구동기를 만들 수는 없습니다.</description></item>
    <item><title>감쇠를 더 키웠는데 왜 더 느려질까?</title><link>https://eigenroom.com/ko/journal/damping-is-not-always-faster</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/damping-is-not-always-faster</guid><pubDate>Sat, 03 Oct 2026 00:00:00 GMT</pubDate><category>물리적 직관</category><description>질량–스프링–댐퍼로 오버슈트·정착·에너지 소산을 구분합니다. 부족·임계·과감쇠 응답을 비교하며 감쇠를 만능 속도 조절기로 생각하지 않는 법을 배웁니다.</description></item>
    <item><title>전압만으로 목표 속도가 나오는데 피드백이 필요할까?</title><link>https://eigenroom.com/ko/journal/open-loop-versus-feedback</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/open-loop-versus-feedback</guid><pubDate>Fri, 02 Oct 2026 00:00:00 GMT</pubDate><category>피드백 기초</category><description>같은 부하에서 전압 유지와 속도 피드백을 비교합니다. 개루프가 유용한 조건, 피드백이 바꾸는 것, 개루프 보드 선도의 다른 의미를 설명합니다.</description></item>
    <item><title>스프링과 RLC 회로가 같은 모양의 식을 갖는 이유</title><link>https://eigenroom.com/ko/journal/mass-spring-damper-and-rlc</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/mass-spring-damper-and-rlc</guid><pubDate>Tue, 29 Sep 2026 00:00:00 GMT</pubDate><category>분야를 잇는 모델링</category><description>질량·감쇠·강성을 인덕턴스·저항·역정전용량에 대응해 봅니다. 수학적 유추와 실제 모터 회로는 구분합니다.</description></item>
    <item><title>역진자 선형화 모델은 언제 도움이 되지 않을까?</title><link>https://eigenroom.com/ko/journal/when-linearization-breaks</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/when-linearization-breaks</guid><pubDate>Tue, 29 Sep 2026 00:00:00 GMT</pubDate><category>모델의 한계</category><description>직립 근처에서 설계한 제어기는 큰 기울기에서 실패할 수 있습니다. 다만 실패한 실행 하나가 근사 오차를 측정해 주지는 않습니다.</description></item>
    <item><title>차분한 그래프가 안정성의 증명은 아니다</title><link>https://eigenroom.com/ko/journal/short-run-is-not-stability</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/short-run-is-not-stability</guid><pubDate>Tue, 29 Sep 2026 00:00:00 GMT</pubDate><category>근거와 안정성</category><description>짧은 시뮬레이션은 입력 하나와 초기조건 하나를 시험할 뿐입니다. BIBO와 내부 안정성은 더 넓은 조건을 말합니다.</description></item>
    <item><title>이득을 조절하기 전에 제어 사양부터 쓰자</title><link>https://eigenroom.com/ko/journal/write-a-control-specification</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/write-a-control-specification</guid><pubDate>Tue, 29 Sep 2026 00:00:00 GMT</pubDate><category>설계 흐름</category><description>'빠르고 안정하게'를 추종·외란 억제·구동기 입력·한계에 대한 관찰 가능한 조건으로 바꿉니다.</description></item>
    <item><title>지연과 우반평면 영점이 빠른 제어를 어렵게 하는 이유</title><link>https://eigenroom.com/ko/journal/delay-and-nonminimum-phase-limits</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/delay-and-nonminimum-phase-limits</guid><pubDate>Tue, 29 Sep 2026 00:00:00 GMT</pubDate><category>주파수 설계의 한계</category><description>늦게 오는 정보와 처음 반대로 움직이는 응답은 서로 다른 현상이며, 둘 다 무리한 빠른 제어의 한계를 만듭니다.</description></item>
    <item><title>모델 방정식 없이 PID를 설계할 수 있을까?</title><link>https://eigenroom.com/ko/journal/pid-without-a-model</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/pid-without-a-model</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>설계 판단</category><description>가능합니다. 하지만 모델이 없다는 말은 근거가 없다는 뜻이 아닙니다. 측정값, 한계, 재현 가능한 조건은 여전히 필요합니다.</description></item>
    <item><title>PID와 상태공간 중 무엇을 쓸까? 질문부터 고치자</title><link>https://eigenroom.com/ko/journal/state-space-or-pid</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/state-space-or-pid</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>설계 판단</category><description>PID는 제어기 계열, 상태공간은 모델 표현, LQR은 그 표현을 사용하는 설계 방법입니다.</description></item>
    <item><title>진상(리드)인가 지상(래그)인가? 보드 선도 다음에는 모터를 보자</title><link>https://eigenroom.com/ko/journal/lead-lag-from-bode-to-motor</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/lead-lag-from-bode-to-motor</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>주파수 설계 실무</category><description>교차점 위상과 저주파 정확도는 다른 목표입니다. 좋은 주파수 선도도 구동기 포화를 숨길 수 있습니다.</description></item>
    <item><title>칼만 추정값이 매끄럽다고 좋은 제어기가 되는 건 아니다</title><link>https://eigenroom.com/ko/journal/kalman-filter-to-lqg</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/kalman-filter-to-lqg</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>상태 추정 실무</category><description>상태 추정과 피드백을 분리해 보고 잡음 가정을 시험한 다음 LQG를 이상적인 전체 상태 LQR과 비교하세요.</description></item>
    <item><title>위상여유가 충분한데 모터가 넘치는 이유는?</title><link>https://eigenroom.com/ko/journal/phase-margin-but-bad-response</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/phase-margin-but-bad-response</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>설계 진단</category><description>선형 여유는 특정 작동 조건의 루프 모델을 말합니다. 입력이 제한된 구동기의 시간 응답은 다를 수 있습니다.</description></item>
    <item><title>진상·지상(리드·래그)·PI, 어떤 문제를 해결하려는가?</title><link>https://eigenroom.com/ko/journal/lead-lag-or-pi</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/lead-lag-or-pi</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>제어기 선택</category><description>보상기를 고르기 전에 같은 모터 목표·부하에서 위상, 지속 오차, 구동기 입력을 비교합니다.</description></item>
    <item><title>계단응답 하나에 맞는다고 모터 모델이 검증되지는 않는다</title><link>https://eigenroom.com/ko/journal/model-fit-is-not-validation</link><guid isPermaLink="true">https://eigenroom.com/ko/journal/model-fit-is-not-validation</guid><pubDate>Sat, 26 Sep 2026 00:00:00 GMT</pubDate><category>모델링 실무</category><description>파라미터 맞춤과 별도 실험 예측은 다른 질문입니다. 설계 모델을 믿기 전에 다른 목표나 부하로 시험하세요.</description></item>
  </channel>
</rss>
