CHAPTER 16 / TIME DOMAIN

The standard second-order system and transient specifications

Two numbers, ζ and ωn, fix the poles, and the poles fix the overshoot, the peak time and the settling time.

THE SHORT ANSWER

The standard second-order system is T(s) = ωn²/(s² + 2ζωn s + ωn²): the damping ratio ζ sets the shape of the step response and the natural frequency ωn sets its time scale. For 0 < ζ < 1 the poles are −ζωn ± jωd with ωd = ωn√(1 − ζ²). Overshoot depends only on ζ, peak time on ωd, and settling time on the decay rate ζωn.

T(s)=ωn2s2+2ζωns+ωn2,Mp=e−πζ/1−ζ2T(s)=\frac{\omega_n^2}{s^2+2\zeta\omega_n s+\omega_n^2},\qquad M_p=e^{-\pi\zeta/\sqrt{1-\zeta^2}}
WHAT YOU WILL LEARN

Given a second-order transfer function, compute ζ, ωn, the poles, tr, tp, Mp and ts by hand; given Mp and ts specifications, find the required ζ, ωn and pole region.

The previous chapter read rise time, overshoot and settling time off a recorded trace. For the standard second-order system the same numbers can be computed from the transfer function before any experiment, and specifications can be turned back into pole locations.

Review the previous lesson: Read a step response
START WITH AN EXAMPLE

First, picture it

Picture a mass on a spring when a constant force is suddenly applied. With little damping it shoots past its new resting point and rings; with heavy damping it creeps there without ringing. Stiffness and mass set how fast it swings, and damping sets how quickly the swinging dies. The standard second-order form separates these two effects: the natural frequency ωn sets the time scale and the damping ratio ζ sets the shape. For a given ζ every step response is the same curve, stretched or compressed along the time axis by ωn. That is why a designer who hears ζ = 0.5 knows at once that the overshoot is about 16%, whatever the hardware.

THE IDEA

Build the idea step by step

Start by writing the transfer function in the standard form ωn²/(s² + 2ζωn s + ωn²). Compare coefficients: the constant term gives ωn, then the s term gives ζ. For 0 < ζ < 1 the poles are a complex pair at −σ ± jωd, with σ = ζωn and ωd = ωn√(1 − ζ²). In the s-plane the pair lies on a circle of radius ωn, at an angle β from the negative real axis with cos β = ζ. Each coordinate controls one specification. The real part σ sets the decay envelope and therefore the settling time. The imaginary part ωd sets the oscillation period and therefore the peak time. The angle β alone sets the overshoot. At ζ = 1 the two poles merge at −ωn, and for ζ > 1 they are real and distinct; in both cases the step response has no overshoot. All formulas in this chapter are for the unit-step response of this exact form with zero initial conditions.

Read the equations

T(s)=C(s)R(s)=ωn2s2+2ζωns+ωn2T(s)=\frac{C(s)}{R(s)}=\frac{\omega_n^2}{s^2+2\zeta\omega_n s+\omega_n^2}

Standard second-order form with unit DC gain. Match your denominator to it: the constant term gives ωn², then the coefficient of s gives ζ. If the numerator is a multiple of ωn², every output value is scaled by that factor and the percent overshoot and all the times stay the same.

s1,2=−ζωn±j ωn1−ζ2=−σ±jωd(0<ζ<1)s_{1,2}=-\zeta\omega_n\pm j\,\omega_n\sqrt{1-\zeta^2}=-\sigma\pm j\omega_d\qquad(0<\zeta<1)

Poles for 0 < ζ < 1. The real part −σ sets how fast the oscillation decays; the imaginary part ωd is the frequency you see in the response.

σ=ζωn,ωd=ωn1−ζ2,∣s1,2∣=ωn,cos⁡β=ζ\sigma=\zeta\omega_n,\qquad \omega_d=\omega_n\sqrt{1-\zeta^2},\qquad |s_{1,2}|=\omega_n,\qquad \cos\beta=\zeta

The s-plane picture. The poles lie on a circle of radius ωn centred at the origin, and the line from the origin to a pole makes the angle β with the negative real axis. A smaller β means a larger ζ.

{0<ζ<1:s1,2=−σ±jωdζ=1:s1,2=−ωn, −ωnζ>1:s1,2=−ζωn±ωnζ2−1\begin{cases}0<\zeta<1: & s_{1,2}=-\sigma\pm j\omega_d\\ \zeta=1: & s_{1,2}=-\omega_n,\ -\omega_n\\ \zeta>1: & s_{1,2}=-\zeta\omega_n\pm\omega_n\sqrt{\zeta^2-1}\end{cases}

Damping classes: underdamped, critically damped and overdamped. Underdamped responses overshoot and oscillate; the other two rise without overshoot. At ζ = 0 the poles are ±jωn and the oscillation never decays.

c(t)=1−e−ζωnt1−ζ2 sin⁡(ωdt+β),β=tan⁡−11−ζ2ζc(t)=1-\frac{e^{-\zeta\omega_n t}}{\sqrt{1-\zeta^2}}\,\sin(\omega_d t+\beta),\qquad \beta=\tan^{-1}\frac{\sqrt{1-\zeta^2}}{\zeta}

Unit-step response for 0 < ζ < 1 with zero initial conditions. It is 1 minus a sinusoid of frequency ωd whose amplitude shrinks along the envelope e^(−ζωn t)/√(1 − ζ²).

tr=π−βωdt_r=\frac{\pi-\beta}{\omega_d}

Rise time, defined here as the first time the response reaches its final value (0–100%), with β in radians. For overdamped systems the 10–90% definition is used instead.

tp=πωdt_p=\frac{\pi}{\omega_d}

Peak time: the first maximum, half a damped period after the step. It depends only on ωd, the imaginary part of the poles.

Mp=c(tp)−c(∞)c(∞)=e−πζ/1−ζ2=e−πσ/ωdM_p=\frac{c(t_p)-c(\infty)}{c(\infty)}=e^{-\pi\zeta/\sqrt{1-\zeta^2}}=e^{-\pi\sigma/\omega_d}

Maximum overshoot, measured from the final value c(∞) and usually quoted in percent. It depends only on ζ: 0.4 gives 25%, 0.5 gives 16%, 0.6 gives 9.5% and 0.7 gives 4.6%.

ts≈4ζωn  (2%),ts≈3ζωn  (5%)t_s\approx\frac{4}{\zeta\omega_n}\ \ (2\%),\qquad t_s\approx\frac{3}{\zeta\omega_n}\ \ (5\%)

Settling time. Both formulas are approximations taken from the decay envelope, whose time constant is 1/(ζωn). The 2% band takes about four time constants and the 5% band about three.

ζ=−ln⁡Mpπ2+ln⁡2Mp\zeta=\frac{-\ln M_p}{\sqrt{\pi^2+\ln^2M_p}}

The overshoot formula solved for ζ, with Mp as a fraction (0.10 for 10%). Use it to turn an overshoot specification into a minimum damping ratio.

ζ≥ζmin⁡  ⟺  β≤cos⁡−1ζmin⁡,ts≤ts,max⁡  ⟺  σ≥4ts,max⁡,tp≤tp,max⁡  ⟺  ωd≥πtp,max⁡\zeta\ge\zeta_{\min}\iff\beta\le\cos^{-1}\zeta_{\min},\qquad t_s\le t_{s,\max}\iff\sigma\ge\frac{4}{t_{s,\max}},\qquad t_p\le t_{p,\max}\iff\omega_d\ge\frac{\pi}{t_{p,\max}}

Specifications as s-plane boundaries. An overshoot limit is a wedge around the negative real axis, a settling-time limit is a vertical line, and a peak-time limit is a horizontal line. The poles must lie inside all of them.

c(t)=1−e−ωnt (1+ωnt)(ζ=1)c(t)=1-e^{-\omega_n t}\,(1+\omega_n t)\qquad(\zeta=1)

Critically damped step response. For a given ωn it is the fastest response of this family that has no overshoot.

Tz(s)=(ωn2/z) (s+z)s2+2ζωns+ωn2⇒cz(t)=c(t)+1z c˙(t)T_z(s)=\frac{(\omega_n^2/z)\,(s+z)}{s^2+2\zeta\omega_n s+\omega_n^2}\quad\Rightarrow\quad c_z(t)=c(t)+\frac1z\,\dot c(t)

A zero at −z, with the DC gain kept at 1, adds a scaled derivative of the original step response. The derivative is positive during the rise, so the response is faster and overshoots more. The effect is small when z is at least 5ζωn.

T3(s)=p ωn2(s+p) (s2+2ζωns+ωn2),p≥5 ζωnT_3(s)=\frac{p\,\omega_n^2}{(s+p)\,(s^2+2\zeta\omega_n s+\omega_n^2)},\qquad p\ge5\,\zeta\omega_n

A third real pole at −p, with the DC gain kept at 1, slows the response and reduces the overshoot. When p is at least five times ζωn the complex pair dominates and the second-order formulas remain good estimates.

What the symbols mean

ζ\zeta
damping ratio, dimensionless
ωn\omega_n
undamped natural frequency, in rad/s
ωd\omega_d
damped natural frequency, in rad/s
σ\sigma
decay rate ζωn, the distance of the poles from the imaginary axis, in s⁻¹
β\beta
angle between the negative real axis and the line from the origin to a pole, in rad
s1,2s_{1,2}
the two poles of T(s), in s⁻¹
T(s)T(s)
closed-loop transfer function from reference to output
R(s),C(s)R(s),C(s)
Laplace transforms of the reference and the output
c(t)c(t)
output response to a unit step, in output units
c(∞)c(\infty)
final value of the output
trt_r
rise time (0–100%), in s
tpt_p
peak time, in s
MpM_p
maximum overshoot as a fraction of c(∞); multiply by 100 for percent
tst_s
settling time for the stated band (2% or 5%), in s
ζmin⁡, ts,max⁡, tp,max⁡\zeta_{\min},\,t_{s,\max},\,t_{p,\max}
specification limits: smallest damping ratio, longest settling time, longest peak time
zz
added zero at s = −z, in s⁻¹
pp
added third pole at s = −p, in s⁻¹
Tz(s), cz(t)T_z(s),\,c_z(t)
transfer function and step response with the added zero
T3(s)T_3(s)
transfer function with the added third pole
KK
loop gain of the running example, in s⁻²

The formulas for tr, tp and Mp are exact for the standard form with 0 < ζ < 1. The settling-time formulas are approximations taken from the exponential envelope. Overshoot is measured from the final value c(∞), which equals the reference only when the steady-state error is zero. A zero or a third pole near the dominant pair changes every one of these numbers.

STEP RESPONSE / T(s) = 4/(s² + 2s + 4)
Mp = 16.3%c(t)c(∞) = 1±2%90%10%tr0.82 stp1.81 sts4.04 st (s)

Exact response of the lectures' running example (ζ = 0.5, ωn = 2 rad/s). 10–90 % rise time tr = 0.82 s, peak 1.163 at tp = 1.81 s, so Mp = 16.3 %. From ts = 4.04 s on, the output stays inside ±2 % of the final value.

WORKED EXAMPLE

The running example T(s) = K/(s² + 2s + K) with K = 4

  1. The plant G(s) = K/[s(s + 2)] under unity negative feedback gives the closed loop below. Take K = 4.

    T(s)=G(s)1+G(s)=Ks2+2s+K=4s2+2s+4(K=4)T(s)=\frac{G(s)}{1+G(s)}=\frac{K}{s^2+2s+K}=\frac{4}{s^2+2s+4}\qquad(K=4)
  2. Match the denominator to the standard form. The constant term gives ωn; the s coefficient then gives ζ.

    ωn2=4 ⇒ ωn=2 rad/s,2ζωn=2 ⇒ ζ=0.5\omega_n^2=4\ \Rightarrow\ \omega_n=2\ \mathrm{rad/s},\qquad 2\zeta\omega_n=2\ \Rightarrow\ \zeta=0.5
  3. Locate the poles. Since 0 < ζ < 1 the system is underdamped.

    σ=ζωn=1 s−1,ωd=21−0.25=3≈1.732 rad/s,s1,2=−1±j1.732\sigma=\zeta\omega_n=1\ \mathrm{s^{-1}},\qquad \omega_d=2\sqrt{1-0.25}=\sqrt3\approx1.732\ \mathrm{rad/s},\qquad s_{1,2}=-1\pm j1.732
  4. Find the pole angle in radians, then the rise time and the peak time.

    β=cos⁡−10.5=π3,tr=π−π/31.732≈1.21 s,tp=π1.732≈1.81 s\beta=\cos^{-1}0.5=\frac{\pi}{3},\qquad t_r=\frac{\pi-\pi/3}{1.732}\approx1.21\ \mathrm s,\qquad t_p=\frac{\pi}{1.732}\approx1.81\ \mathrm s
  5. Compute the maximum overshoot. The final value is T(0) = 1, so the peak value is 1.163.

    Mp=e−π(0.5)/0.75=e−1.814≈0.163  (16.3%),c(tp)=1.163M_p=e^{-\pi(0.5)/\sqrt{0.75}}=e^{-1.814}\approx0.163\ \ (16.3\%),\qquad c(t_p)=1.163
  6. Estimate the settling time from σ. A numerical simulation gives 4.04 s for the 2% band and 2.64 s for the 5% band, so treat these as estimates.

    ts≈4σ=4 s  (2%),ts≈3σ=3 s  (5%)t_s\approx\frac{4}{\sigma}=4\ \mathrm s\ \ (2\%),\qquad t_s\approx\frac{3}{\sigma}=3\ \mathrm s\ \ (5\%)
  7. Now raise the gain to K = 16. The real part stays at σ = 1 s⁻¹, so the settling time does not improve. The response peaks sooner and overshoots much more.

    K=16:ωn=4 rad/s,ζ=0.25,Mp≈44.4%,tp≈0.81 s,ts≈4 sK=16:\quad \omega_n=4\ \mathrm{rad/s},\quad \zeta=0.25,\quad M_p\approx44.4\%,\quad t_p\approx0.81\ \mathrm s,\quad t_s\approx4\ \mathrm s
REFERENCE

Reference tables

Step-response specifications of T(s) = ωn²/(s² + 2ζωn s + ωn²), 0 < ζ < 1
SpecificationFormulaRemark
Poless1,2=−ζωn±jωd,  ωd=ωn1−ζ2s_{1,2}=-\zeta\omega_n\pm j\omega_d,\ \ \omega_d=\omega_n\sqrt{1-\zeta^2}|s| = ωn and cos β = ζ
Rise timetr=π−βωdt_r=\dfrac{\pi-\beta}{\omega_d}from 0 to 100% of the final value
Peak timetp=πωdt_p=\dfrac{\pi}{\omega_d}time of the first peak
Maximum overshootMp=e−πζ/1−ζ2M_p=e^{-\pi\zeta/\sqrt{1-\zeta^2}}fraction of the final value; depends on ζ only
Settling time (2%)ts≈4ζωnt_s\approx\dfrac{4}{\zeta\omega_n}envelope estimate
Settling time (5%)ts≈3ζωnt_s\approx\dfrac{3}{\zeta\omega_n}envelope estimate
Damping from overshootζ=−ln⁡Mpπ2+ln⁡2Mp\zeta=\dfrac{-\ln M_p}{\sqrt{\pi^2+\ln^2M_p}}inverse of the overshoot formula
Normalized specifications by damping ratio
ζ\zetaMp (%)β = cos⁻¹ζ (°)ωntr\omega_n t_rωntp\omega_n t_pωn·ts (2%)
0.172.984.31.683.1640.0
0.252.778.51.813.2120.0
0.337.272.51.973.2913.3
0.425.466.42.163.4310.0
0.516.360.02.423.638.0
0.69.553.12.773.936.7
0.74.645.63.294.405.7
0.81.536.94.165.245.0
0.90.225.86.177.214.4

Divide the last three columns by ωn in rad/s to get seconds. The settling column uses the 4/(ζωn) envelope estimate, so it is approximate; the other columns are exact for the standard second-order system.

More detail and model assumptions
A CLOSER LOOK

Where the step-response formulas come from

The unit-step response is C(s) = ωn²/[s(s² + 2ζωn s + ωn²)]. Expand it as in the chapter on inverse Laplace transforms: C(s) = 1/s − (s + 2ζωn)/[(s + σ)² + ωd²]. Splitting the numerator into (s + σ) + σ and inverting gives c(t) = 1 − e^(−σt)[cos ωd t + (σ/ωd) sin ωd t]. Because σ/ωd = ζ/√(1 − ζ²), the cosine and sine combine into one sine of amplitude 1/√(1 − ζ²) and phase β, which is the formula in the list.

Differentiate: ċ(t) = [ωn/√(1 − ζ²)] e^(−σt) sin ωd t. The slope is zero whenever ωd t = nπ, and the first maximum is at n = 1, so tp = π/ωd. Substituting back gives c(tp) = 1 + e^(−σπ/ωd), and the excess over the final value 1 is Mp = e^(−πζ/√(1−ζ²)). The response first reaches 1 when sin(ωd t + β) = 0, that is when ωd tr + β = π.

The response stays between the envelope curves 1 ± e^(−σt)/√(1 − ζ²). Asking when e^(−σt) falls to 0.02 gives t = 3.91/σ, rounded to 4/σ; for 0.05 it gives 3.00/σ. These are estimates. The true settling time depends on which swing is the last to leave the band: for ζ = 0.5 and ωn = 2 rad/s the exact values are 4.04 s (2%) and 2.64 s (5%), against 4 s and 3 s from the formulas.

A CLOSER LOOK

From specifications to a pole region

Each transient specification is a boundary in the s-plane. An overshoot limit Mp ≤ Mp,max requires ζ ≥ ζmin, so the poles must lie inside the wedge β ≤ cos⁻¹ ζmin around the negative real axis. A settling-time limit ts ≤ ts,max requires σ ≥ 4/ts,max, so the poles must lie to the left of a vertical line. A peak-time limit tp ≤ tp,max requires ωd ≥ π/tp,max, so the poles must lie above a horizontal line, with the mirror image below the real axis.

Example: Mp ≤ 10% and ts ≤ 2 s (2% band). The overshoot formula inverted gives ζ ≥ 0.591, that is β ≤ 53.8°. The settling requirement gives σ ≥ 2 s⁻¹. The corner of the allowed region is s = −2 ± j2.73, which corresponds to ωn = 3.38 rad/s. Any pole pair inside the region meets both specifications.

Apply this to the running example T(s) = K/(s² + 2s + K). Its real part is σ = 1 s⁻¹ for every K > 1, so the gain moves the poles straight up and down the line Re(s) = −1. Raising K increases ωd, which shortens the peak time, and lowers ζ, which raises the overshoot. The settling time stays near 4 s. To settle faster you must change the plant or the controller structure; gain alone will not do it.

A CLOSER LOOK

Dominant poles, a third pole and a zero

A higher-order response is a sum of modes, one per pole, and each mode decays as fast as its pole's real part. Poles far to the left die out quickly and usually carry small coefficients. The pair nearest the imaginary axis therefore shapes most of the response: these are the dominant poles. As a working rule, when every other pole and zero is at least five times farther left than σ, the second-order formulas give good estimates.

Add a third pole to the worked example while keeping the DC gain at 1: T₃(s) = 4p/[(s + p)(s² + 2s + 4)]. The second-order values are Mp = 16.3% and tp = 1.81 s. With p = 10 the simulation gives 15.9% and 1.92 s, almost unchanged. With p = 2 it gives 8.1% and 2.46 s, and with p = 1 the overshoot disappears. An extra pole acts as a lag: it slows the response and lowers the overshoot.

Now add a zero instead: T_z(s) = (4/z)(s + z)/(s² + 2s + 4). The step response becomes c(t) + ċ(t)/z, the original response plus a scaled copy of its derivative. With z = 10 the overshoot is 16.7%; with z = 2 it is 29.8% at tp = 1.21 s; with z = 1 it reaches 69.9%. A left-half-plane zero speeds up the rise and raises the overshoot, while the poles and the decay rate stay the same.

A CLOSER LOOK

Critical damping and overdamping

At ζ = 1 both poles sit at −ωn and the step response is c(t) = 1 − e^(−ωn t)(1 + ωn t). It rises without overshoot; for a given ωn, no response of this family without overshoot is faster. Peak time and maximum overshoot are not defined here, and the rise time is measured from 10% to 90% of the final value.

For ζ > 1 the poles are real: s = −ζωn ± ωn√(ζ² − 1). Take ωn = 4 rad/s and ζ = 1.25: the poles are −2 and −8, and partial fractions give c(t) = 1 − (4/3)e^(−2t) + (1/3)e^(−8t). The e^(−8t) term is gone within about half a second, and the slow pole at −2 controls the rest. Increasing the damping further moves the slow pole toward the origin and lengthens the tail.

TRY IT

Connect the example to the lab

Open the mass–spring–damper step experiment: m = 1 kg, k = 16 N/m, c = 1.6 N·s/m, with a 2 N step. Then ωn = √(k/m) = 4 rad/s and ζ = c/(2√(km)) = 0.2. The formulas predict Mp = 52.7%, tp = 0.80 s, a peak of 0.125 × 1.527 = 0.191 m, and ts ≈ 5 s for the 2% band. Run it: the overshoot reading should be about 52.7% and the 2% settling time about 4.9 s. The lab reports the 10–90% rise time (about 0.30 s), which is a different definition from the 0–100% formula (0.45 s).

Check the overshoot formula on a mass–spring–damper
YOUR EXPERIMENT

Make a prediction before moving a control.

  1. PREDICTFor m = 1 kg, k = 16 N/m, c = 1.6 N·s/m and a 2 N step, compute ζ, ωn, the percent overshoot and the peak displacement before you run anything.
  2. CHANGE ONE THINGRun the baseline and pin it. Then change only the damping to c = 3.2 N·s/m, which doubles ζ to 0.4, and predict the new overshoot before you run again.
  3. OBSERVECompare the overshoot readings with 52.7% and 25.4%, and the peak times with 0.80 s and 0.86 s. Both runs should settle at the same 0.125 m.
  4. EXPLAINUse the Mp formula to explain why doubling ζ more than halved the overshoot, and use the static balance kx = F to explain why the final displacement did not move.
BE CAREFUL

Check three things before you use these formulas: the numerator is a constant (no zero), no other pole lies near the dominant pair, and 0 < ζ < 1. Measure percent overshoot from the final value c(∞), not from the reference; the two differ whenever there is steady-state error.

Check your understanding+

Two designs have closed-loop poles at −2 ± j2 and at −4 ± j4. Which one has the larger overshoot, and which one settles faster?

The overshoot is the same. Both pairs lie on the ray β = 45°, so ζ = 0.707 and Mp = e^(−π) ≈ 4.3%. The second pair has twice the σ and settles in half the time: ts ≈ 4/4 = 1 s against 4/2 = 2 s.
PRACTICE PROBLEMS

Solve these before opening the solutions

Work each problem on paper first. Open the answer to check yours, then the full solution if you need the steps, and mark how it went.

  1. For the unit-step response of G(s), find ωn, ζ, the poles, the peak time, the percent overshoot and the 2% settling time.

    G(s)=25s2+6s+25G(s)=\frac{25}{s^2+6s+25}
    Show answer

    AnswerAn underdamped system with poles at −3 ± j4.

    ωn=5 rad/s,ζ=0.6,tp≈0.785 s,Mp≈9.5%,ts≈1.33 s\omega_n=5\ \mathrm{rad/s},\quad \zeta=0.6,\quad t_p\approx0.785\ \mathrm s,\quad M_p\approx9.5\%,\quad t_s\approx1.33\ \mathrm s
    Show full solution

    Solution

    1. Match coefficients with the standard form.

      ωn2=25 ⇒ ωn=5 rad/s,2ζωn=6 ⇒ ζ=0.6\omega_n^2=25\ \Rightarrow\ \omega_n=5\ \mathrm{rad/s},\qquad 2\zeta\omega_n=6\ \Rightarrow\ \zeta=0.6
    2. Compute the real and imaginary parts of the poles.

      σ=0.6×5=3 s−1,ωd=51−0.36=4 rad/s,s1,2=−3±j4\sigma=0.6\times5=3\ \mathrm{s^{-1}},\qquad \omega_d=5\sqrt{1-0.36}=4\ \mathrm{rad/s},\qquad s_{1,2}=-3\pm j4
    3. Use ωd for the peak time and the ratio σ/ωd for the overshoot.

      tp=π4≈0.785 s,Mp=e−π(3/4)=e−2.356≈0.095t_p=\frac{\pi}{4}\approx0.785\ \mathrm s,\qquad M_p=e^{-\pi(3/4)}=e^{-2.356}\approx0.095
    4. Use σ for the 2% settling time.

      ts≈43≈1.33 st_s\approx\frac{4}{3}\approx1.33\ \mathrm s
  2. A unit step is applied to G(s), whose DC gain is not 1. Find the final value, the percent overshoot, and the value and time of the first peak.

    G(s)=20s2+2s+10G(s)=\frac{20}{s^2+2s+10}
    Show answer

    AnswerThe output settles at 2 and overshoots that final value by 35.1%.

    c(∞)=2,Mp≈35.1%,c(tp)≈2.70,tp≈1.05 sc(\infty)=2,\qquad M_p\approx35.1\%,\qquad c(t_p)\approx2.70,\qquad t_p\approx1.05\ \mathrm s
    Show full solution

    Solution

    1. The poles are in the left half-plane, so the final value of the unit-step response is G(0).

      c(∞)=lim⁡s→0s⋅G(s)s=2010=2c(\infty)=\lim_{s\to0}s\cdot\frac{G(s)}{s}=\frac{20}{10}=2
    2. Read ωn and ζ from the denominator, then the pole coordinates.

      ωn=10≈3.16 rad/s,ζ=2210≈0.316,σ=1 s−1,ωd=10−1=3 rad/s\omega_n=\sqrt{10}\approx3.16\ \mathrm{rad/s},\qquad \zeta=\frac{2}{2\sqrt{10}}\approx0.316,\qquad \sigma=1\ \mathrm{s^{-1}},\qquad \omega_d=\sqrt{10-1}=3\ \mathrm{rad/s}
    3. Overshoot and peak time depend only on the denominator.

      Mp=e−πσ/ωd=e−π/3≈0.351,tp=π3≈1.05 sM_p=e^{-\pi\sigma/\omega_d}=e^{-\pi/3}\approx0.351,\qquad t_p=\frac{\pi}{3}\approx1.05\ \mathrm s
    4. Overshoot is a fraction of the final value, so the peak is 2 times 1.351.

      c(tp)=c(∞) (1+Mp)=2×1.351≈2.70c(t_p)=c(\infty)\,(1+M_p)=2\times1.351\approx2.70
  3. A mass–spring–damper has m = 2 kg, c = 8 N·s/m and k = 50 N/m. It is at rest when a constant 10 N force is applied. Find ζ, ωn, the final displacement, the peak displacement and its time, and the 2% settling time.

    2x¨+8x˙+50x=10⋅1(t),x(0)=x˙(0)=02\ddot x+8\dot x+50x=10\cdot1(t),\qquad x(0)=\dot x(0)=0
    Show answer

    AnswerThe mass settles at 0.20 m after peaking at about 0.251 m.

    ζ=0.4,ωn=5 rad/s,xmax⁡≈0.251 m,tp≈0.686 s,ts≈2 s\zeta=0.4,\quad \omega_n=5\ \mathrm{rad/s},\quad x_{\max}\approx0.251\ \mathrm m,\quad t_p\approx0.686\ \mathrm s,\quad t_s\approx2\ \mathrm s
    Show full solution

    Solution

    1. Divide the transfer function by m to expose the standard denominator.

      X(s)F(s)=12s2+8s+50=0.5s2+4s+25 ⇒ ωn=5 rad/s,ζ=42×5=0.4\frac{X(s)}{F(s)}=\frac{1}{2s^2+8s+50}=\frac{0.5}{s^2+4s+25}\ \Rightarrow\ \omega_n=5\ \mathrm{rad/s},\quad \zeta=\frac{4}{2\times5}=0.4
    2. The final displacement is the static balance kx = F.

      x(∞)=Fk=1050=0.20 mx(\infty)=\frac{F}{k}=\frac{10}{50}=0.20\ \mathrm m
    3. Compute ωd, the peak time and the overshoot.

      ωd=51−0.16≈4.583 rad/s,tp=π4.583≈0.686 s,Mp=e−π(0.4)/0.84≈0.254\omega_d=5\sqrt{1-0.16}\approx4.583\ \mathrm{rad/s},\qquad t_p=\frac{\pi}{4.583}\approx0.686\ \mathrm s,\qquad M_p=e^{-\pi(0.4)/\sqrt{0.84}}\approx0.254
    4. Scale the overshoot by the final displacement and estimate the settling time from σ = 2 s⁻¹.

      xmax⁡=0.20×1.254≈0.251 m,ts≈42=2 sx_{\max}=0.20\times1.254\approx0.251\ \mathrm m,\qquad t_s\approx\frac{4}{2}=2\ \mathrm s
  4. A recorded unit-step response settles at 0.8. Its first and highest peak is 1.0 at t = 0.5 s. Assume a second-order system with no zeros and identify ζ, ωn and the transfer function.

    Show answer

    AnswerOvershoot gives ζ, peak time gives ωd, and the final value gives the DC gain.

    ζ≈0.404,ωn≈6.87 rad/s,G(s)≈37.7s2+5.55s+47.2\zeta\approx0.404,\qquad \omega_n\approx6.87\ \mathrm{rad/s},\qquad G(s)\approx\frac{37.7}{s^2+5.55s+47.2}
    Show full solution

    Solution

    1. Measure the overshoot from the final value, not from 1.

      Mp=1.0−0.80.8=0.25M_p=\frac{1.0-0.8}{0.8}=0.25
    2. Invert the overshoot formula to get ζ.

      ζ=−ln⁡0.25π2+ln⁡20.25=1.3863.434≈0.404\zeta=\frac{-\ln0.25}{\sqrt{\pi^2+\ln^2 0.25}}=\frac{1.386}{3.434}\approx0.404
    3. The peak time gives ωd, and ζ converts it to ωn.

      ωd=π0.5≈6.283 rad/s,ωn=6.2831−0.4042≈6.87 rad/s\omega_d=\frac{\pi}{0.5}\approx6.283\ \mathrm{rad/s},\qquad \omega_n=\frac{6.283}{\sqrt{1-0.404^2}}\approx6.87\ \mathrm{rad/s}
    4. The DC gain is the final value 0.8, so the numerator is 0.8ωn².

      G(s)=0.8 ωn2s2+2ζωns+ωn2≈37.7s2+5.55s+47.2G(s)=\frac{0.8\,\omega_n^2}{s^2+2\zeta\omega_n s+\omega_n^2}\approx\frac{37.7}{s^2+5.55s+47.2}
  5. A plant G(s) = K/[s(s + 4)] is placed under unity negative feedback. (a) Find K for 10% overshoot. (b) Find the resulting peak time and 2% settling time. (c) Can a 2% settling time of 1 s be met by changing K alone? If the plant pole is moved from −4 to −a, find a and K that give 10% overshoot and ts ≈ 1 s.

    T(s)=Ks2+4s+KT(s)=\frac{K}{s^2+4s+K}
    Show answer

    AnswerK ≈ 11.4 gives tp ≈ 1.15 s and ts ≈ 2 s. Gain alone cannot shorten ts because σ = 2 s⁻¹ for every K; a = 8 with K ≈ 45.8 meets both specifications.

    (a) K≈11.4(b) tp≈1.15 s, ts≈2 s(c) a=8, K≈45.8\mathrm{(a)}\ K\approx11.4\qquad \mathrm{(b)}\ t_p\approx1.15\ \mathrm s,\ t_s\approx2\ \mathrm s\qquad \mathrm{(c)}\ a=8,\ K\approx45.8
    Show full solution

    Solution

    1. Match the closed-loop denominator to the standard form. The s coefficient fixes σ whatever the gain.

      ωn=K,2ζωn=4 ⇒ σ=ζωn=2 s−1\omega_n=\sqrt K,\qquad 2\zeta\omega_n=4\ \Rightarrow\ \sigma=\zeta\omega_n=2\ \mathrm{s^{-1}}
    2. Turn the 10% overshoot specification into a damping ratio.

      ζ=−ln⁡0.10π2+ln⁡20.10=2.3033.895≈0.591\zeta=\frac{-\ln0.10}{\sqrt{\pi^2+\ln^2 0.10}}=\frac{2.303}{3.895}\approx0.591
    3. With σ = 2 fixed, ζ determines ωn and therefore K.

      ωn=σζ=20.591≈3.38 rad/s,K=ωn2≈11.4\omega_n=\frac{\sigma}{\zeta}=\frac{2}{0.591}\approx3.38\ \mathrm{rad/s},\qquad K=\omega_n^2\approx11.4
    4. Compute ωd, then the peak time and the settling time.

      ωd=3.381−0.5912≈2.73 rad/s,tp=π2.73≈1.15 s,ts≈42=2 s\omega_d=3.38\sqrt{1-0.591^2}\approx2.73\ \mathrm{rad/s},\qquad t_p=\frac{\pi}{2.73}\approx1.15\ \mathrm s,\qquad t_s\approx\frac{4}{2}=2\ \mathrm s
    5. Gain cannot change σ, so ts stays near 2 s. A settling time of 1 s needs σ = 4 s⁻¹. With the denominator s² + as + K that means a = 2σ = 8; the same ζ then gives ωn and K.

      σ=41=4 s−1 ⇒ a=8,ωn=40.591≈6.77 rad/s,K=ωn2≈45.8\sigma=\frac{4}{1}=4\ \mathrm{s^{-1}}\ \Rightarrow\ a=8,\qquad \omega_n=\frac{4}{0.591}\approx6.77\ \mathrm{rad/s},\qquad K=\omega_n^2\approx45.8

Mark each exercise after you check your answer. Marks stay in this browser.

KEY TERMS

Terms this lecture teaches

All terms in the glossary →
QUESTIONS STUDENTS ASK

Frequently asked questions

What damping ratio gives 10% overshoot?

Invert the overshoot formula: ζ = −ln Mp / √(π² + ln² Mp), with Mp as a fraction. For Mp = 0.10 this gives ζ ≈ 0.591, so the poles must lie within about 53.8° of the negative real axis to keep overshoot at or below 10%.

Why does raising the gain increase overshoot but not shorten settling time?

In the loop K/(s² + 2s + K), the real part of the poles stays at −1 for every K > 1, so the gain only moves them vertically. K = 4 gives ζ = 0.5 and 16.3% overshoot, K = 16 gives ζ = 0.25 and 44.4%, while the estimate ts ≈ 4/(ζωn) stays at 4 s in both cases.

Is percent overshoot measured from the reference or from the final value?

From the final value c(∞). The formula Mp = e^(−πζ/√(1 − ζ²)) describes how far the peak exceeds the value the response settles at, and that value equals the reference only when there is no steady-state error.

Which rise-time definition should I use, 0–100% or 10–90%?

The formula tr = (π − β)/ωd uses 0–100%: the first time an underdamped response reaches its final value. A critically damped or overdamped response approaches the final value without crossing it, so use 10–90% there. Always state which definition a reported rise time uses.

When do the second-order formulas work for a higher-order system?

When one complex pole pair dominates. As a working rule, every other pole and zero should be at least five times farther from the imaginary axis than that pair. A nearby extra pole slows the response and lowers the overshoot; a nearby left-half-plane zero speeds up the rise and raises the overshoot.

Why the next lesson follows

Every formula here assumes the poles are in the left half-plane, so that the transient dies out. The next chapter asks that question directly: when is a loop stable, and how much error remains once the transient is gone?

YOUR PROGRESS

Finished the reading and the exercises? Mark the lecture as done to tick it on the syllabus. Progress stays in this browser.

EIGENROOM · https://eigenroom.com/theory/second-order-specs · Updated 2026-11-15